欧美一级在线观看_91热久久免费频精品黑人99_AV无码AV高潮AV喷吹免费_亚洲六月丁香六月婷婷色伊人,国产亚洲综合久久系列,欧美日韩高清在线 ,婷婷综合久久中文字幕蜜桃三电影

Can we help you find something?

News
Location : Home> News>Industry News

Some common problems and treatment methods in the UV printing process

Click:[1237] Publish Time:2019-09-16

1.Design plate making 

  The design of UV printing must be based on the work order to determine the output format, 

   such as film surface sweep or back sweep, output network cable and network cable angle. 

   Some special printing requirements are higher, such as 3D printing, the resolution is relatively high, 

   the cable angle must match the printing material to avoid hitting the net; transparent plastic sheets and aluminized paper 

   often need to be printed with white ink, should pay attention to the printing material expansion and contraction 

   The effect is to correct the film in advance to achieve the best quality.


2.The adhesion 

   Because the plastic sheet or gold and silver cardboard and other substrates have poor permeability, 

   the adsorption of ink is relatively weak, so even with UV ink printing, the ink adhesion is relatively poor,

   the printing quality is not high. This problem can be solved by surface treatment of the material.


3.Ink emulsification 

   UV ink ink balance latitude is relatively narrow, it is easy to cause ink emulsification, dirty version, 

   affecting the printing quality. Solution: Reduce the printing speed and control the printing 

   speed to 5000~8000 prints/hour.


4. The color sequence arrangement 

    Due to the limitation of the principle of ink, the ink layer on the substrate is relatively thin. 

    When a thick ink layer is needed, the printed matter is difficult to achieve the desired copying effect. 

    For example, when four-color overprinting, the commonly used printing color sequence is black, cyan, 

    magenta, and yellow, because black almost fills all the space, cyan, magenta, 

    and yellow have lower inking power, and the total amount of ink is not enough. 

    Causes the color to be insufficient. Solution: Change the color sequence, first print a small amount of ink, 

    and finally print a large amount of black, so that the amount of ink can be maximized and the color is fuller.


5. The degree of curing is to increase the saturation of the color of the printed matter. 

    When UV printing is performed on the surface of the substrate such as plastic sheet, 

    the printing pressure cannot be adjusted greatly. Firstly, the printing speed should be moderately reduced, 

    so that the irradiation time of the UV lamp is appropriately lengthened. 

    The ink is completely cured; the distance between the UV lamp and the substrate is adjusted, 

    and the intensity of the UV light is increased to solidify the ink.


主站蜘蛛池模板: 济阳县| 若尔盖县| 克什克腾旗| 开化县| 基隆市| 左贡县| 大兴区| 青州市| 航空| 南昌县| 雅安市| 永宁县| 景谷| 栖霞市| 阿拉善左旗| 桃园县| 越西县| 胶南市| 崇义县| 武冈市| 江永县| 和平县| 黄石市| 平塘县| 肥西县| 乐亭县| 社会| 蕲春县| 卫辉市| 霞浦县| 金湖县| 斗六市| 塘沽区| 梁河县| 陈巴尔虎旗| 穆棱市| 淄博市| 类乌齐县| 历史| 双鸭山市| 德令哈市|